Company Details

  • HAFID INTERNATIONAL LIMITED

  •  [Zhejiang,China]
  • Business Type:Manufacturer
  • Main Mark: Americas , Europe , Middle East
  • Exporter:41% - 50%
  • Certs:GS, ISO9001, ISO9002, ISO14001, ISO14004, ISO/TS16949
Inquiry Basket ( 0 )

HAFID INTERNATIONAL LIMITED

Home > Video > Video Display > 4g63t Motor startup

4g63t Motor startup

Hey guys i took a quick video of the motor starting up just to prove it works before i started to part out my car.This was my fully built motor in my 99 Eclipse.Bottom End
Cryo-treated  Eagle 4340 Steel crankshaft
Eagle forged connecting rods H beam
Wiseco 8:3:1 85.5mm (20 thou overbore) forged pitons
Wiseco Rings
ARP head studs, main studs, rod bolts
ACL Tri-Metal Race series Main Bearings
ACL Tri-Metal Race series Rod Bearings
Buschur Racing Harmonic under drive pulley
OBX
New Topline  water pump
New OEM oil pumpTiming
AEM true time cam gears
Greddy Timing BeltHead
Head resurfaced, head cleaned valves re seated, ported, polished and Pressure tested
HKS 272/272 Cams
Ferrea Titanium Valves 6000 series
Ferrera Valve locks
HKS springs
Viton valve stem seals
Cometic MLS (Multi Layer Steel) head gasket
Topline Complete gasket setTurbo, exhaust and Intake
Garrett GT30R Dual ball bearing, twin scroll T3/T4 hybrid matched with Tial GT-35r with the cast SS exhaust housing (rated for 600+ HP)
Ceramic coated Stage 3 Stainless steel equal length header with 41 mm flange and Titanium Exhaust Wrap
Tial 41 mm Wastegate with 18 psi springs
VRS 2.5″  Front mount intercooler (Bar and plate 3.5x10x34)
HKS SSQV 2 blow off valve
3 ” ExoticSpeed R1-T complete turbo back exhaust
Forced Performance Intake pipe ( 4 inch inlet)
MAF removed/switched to speed densityCooling
Mishimoto Aluminum Race Rad
Flex-a-Lite Rad Fan
Devils own stage 1 Meth kitFuel
Walboro 255 LPH fuel pump
PCI 880 cc injectors
Aeromotive Fuel regulator with 100 PSI Motometer GaugeDrive Train
Brand new Mitsubishi OEM Transmission (2009 Not a rebuild) Redline Synthetic Oil
Fidanza stage 3.2 Carbon Kevlar 4 puck Performance clutch (511 ft/lbs)
Fidanza Aluminum 8 pnd lightened flywheelElectronics
Eprom ECU with DSMLink v3
1G CAS
Greddy Turbo Timer
Autometer Boost Gauge
Autometer Pro-Comp Ultra-Lite Oil temp gauge
Autometer Pro-Comp Ultra-Lite Oil gauges
AEM Wideband 02
Optoma Yellow Top Battery Suspension/Brakes
Tein Super Street adjustable Coilovers with 16 way adjustable Damper
SPC Performance control arms with adjustable ball joints
New OEM wheel bearings and lower control arms
18 inch Enkei Rims with Pirelli Tires
Upgraded to 2G AWD dual piston caliper’s and rotors.
Rear strut/Sway barMiscellaneousRed Prothane Motor mounts
All coolant and oil lines replaced with SS braided lines
ECU controlled boost controller with per gear boost.
Gates 170* thermostat
NGK copper plugsFully Built 7 bolt 4G63-T from a 99 block with split bearings (new bearing design introduced in 98 to prevent crank-walk)Engine was built by Gord Bush to rev to 10,000rpm+ reliably and can easily handle 1000+ HP
Communicate with Supplier?Supplier
jack Mr. jack
What can I do for you?